Multimeter Test Leads Compared: 3 Listings
As an Amazon Associate we earn from qualifying purchases.
Multimeter test leads are the cables, probes and clips that connect a meter to the circuit it measures. This page compares three listings whose titles name multimeter test leads. For each one it reports the stated category rating, the current rating, the lead lengths, the included parts and the compatible meters, and it shows where a listing’s figures disagree with another part of the same listing.
The three listings describe very different sets. One is a 24-piece kit with many probe types, one is a pair of silicone leads with threaded clips, and one is a set of replacement leads. Their ratings and lengths are not interchangeable, so compare each figure with the listing it came from.
Quick answer
All three listings state a CAT III 1000V rating. Two of them also state CAT IV 600V, which the 24-piece set does not mention. For a current rating, the SuperDi replacement leads state 20 A, the 24-piece set states 10 A, and the WG-011 silicone leads state 10 A on the threaded clip rather than on the leads as a whole.
If you need the most parts in one box, the 24-piece set has the largest stated part count (24). If you need a pair of leads with listed lengths and a clip rating, the WG-011 listing gives the most length detail. If you need a 20 A current figure, only the SuperDi listing states one.
Comparison table
| Listing | Stated category rating | Stated current rating | Stated lead length | Included or compatible |
|---|---|---|---|---|
| 24 Pcs Multimeter Test Leads Set, Young Dance (first listing) | CAT III 1000V (specification field and title) | 10 A (title and specification field) | 100 cm and 70 cm banana plug leads (bullets) | 24-piece set with probes, clips and hooks; compatible with Fluke, KAIWEETS and INNOVA meters (title) |
| WG-011 Silicone Multimeter Leads, WGGE (second listing) | CAT III 1000V and CAT IV 600V (item highlight); IEC certified category III up to 1,000V (bullets) | 10 Amps on the threaded alligator clip (bullets) | 40 inch lead wire; 47 inch test lead length (bullets) | Two leads, two threaded probe tips, two threaded clips and two safety clips (bullets) |
| NEW Meter Test Leads, SuperDi (third listing) | CAT III 1000V and CAT IV 600V (bullets) | 20 A (title and bullets) | 42 inches, approximately (bullets) | Standard jack probe; compatible with FLUKE, Ideal and Simpson meters (bullets and specification field) |
The first listing: 24-piece multimeter test leads set
The listing names Young Dance and carries a title for a 24-piece multimeter test lead set with alligator clips, insulation piercing test clips and test probes, rated 1000V and 10A CAT III. Its specification fields give dimensions of 7.87 x 3.94 x 0.98 inches, a unit count of 24, a color of red, and compatibility with multimeters and voltmeters. The listing names Fluke, KAIWEETS and INNOVA meters as examples of compatible brands.
The bullets describe soft, high grade silicone insulation and a lead wire rated CAT III 1000V and 10A. They describe a banana plug and probe head that connects to other accessories with a 4mm socket, and interchangeable piercing probes, alligator clips, test hooks and back probes. The bullets list two 100 cm banana plug test leads and two 70 cm banana plug to test hook leads, then add extension probes, U-shaped banana plugs, connecting bananas and several probe and clip types in pairs.
- Category: CAT III 1000V (title, bullets and specification field)
- Current: 10A (title, bullets and specification field)
- Lengths: 100 cm and 70 cm banana plug leads (bullets)
- Contents: 24 pieces, including piercing clips and back probes (bullets)
The specification fields give a power source of battery powered. That does not apply to a set of leads, so treat the field as a labeling detail to confirm on the product page.
The second listing: WG-011 silicone multimeter leads
The listing names WGGE and model WG-011, with a title that describes silicone multimeter leads with safety alligator clips. Its item highlight field reads CAT III 1000V and CAT IV 600V rated, with threaded clip connections and flexible leads. The specification fields give colors of black and red, an item weight of 4.7 ounces, dimensions of 7 x 3.5 x 0.6 inches, and a standard of IEC 61326.
The bullets say the set includes two soft silicone test leads, two threaded safety alligator clips and two threaded alligator clips in two colors. They give a lead wire length of 40 inches and a test lead length of 47 inches, with shrouded 4mm banana plugs at the ends. The safety clip has a jaw opening of 0.5 inches and is made of nickel-plated brass in a glass-filled nylon housing. The threaded clip uses an 8-32 barrel with a jaw opening of 0.31 inches (7.9 mm) at the maximum and is rated 10 Amps. The bullets say the set is IEC certified for category III installations up to 1,000V, and that the leads can withstand low temperatures of -68 ℉.
- Category: CAT III 1000V and CAT IV 600V (item highlight); category III up to 1,000V (bullets)
- Current: 10 Amps on the threaded clip (bullets)
- Lengths: 40 inch lead wire; 47 inch test lead length (bullets)
- Clips: safety and threaded alligator clips, nickel-plated (bullets)
The lead wire is listed at 40 inches and the test lead length at 47 inches. Those two figures are both in the bullets, and the listing does not explain the difference, so check the product page for the length you will use.
The third listing: NEW meter test leads, SuperDi
The listing names SuperDi and carries a title for new meter test leads rated CAT III 1000V and 20A, offered as a replacement for Fluke, Ideal and Simpson meters. Its specification fields give a measurement type of multimeter, a style of industrial, colors of red and black, an item weight of 2.39 ounces, and a model number of 6203807431532.
The bullets state a rating of CAT III 1000V and CAT IV 600V at 20A, a standard jack probe length of about 42 inches, and a plug diameter of 0.8 cm (5/16 inch). They say the wire is premium material that stays flexible and resists breaking, and that the joints are finished for firm contact. They describe compatibility with Fluke, Ideal and Simpson meters and a range of uses from electronic maintenance to industrial automation.
- Category: CAT III 1000V and CAT IV 600V (bullets)
- Current: 20A (title and bullets)
- Length: about 42 inches, standard jack probe (bullets)
- Plug: 0.8 cm (5/16 inch) diameter (bullets)
This is the only listing of the three that states a 20A figure. The bullets refer to the 20A probe, so the rating applies to the probe as listed rather than to every part of the set.
How these three were chosen
Each listing above has a title that names multimeter test leads. Other products in related results, including USB testers, pen testers, automotive test lights and a voltage detector, are left out because they are not test lead sets. Figures come from each listing’s own fields and bullets. The first listing was checked on 2026-10-11, and the other two on 2026-10-20.
Worked example: a 15 A current against the three ratings
Take a 15 A current as an illustration. The 24-piece set states a 10A rating, so a 15 A current is above the figure in its title and specification field. The WG-011 states 10 Amps on its threaded clip, so the same current is above that clip rating too. The SuperDi listing states 20A, so the 15 A current falls under its stated figure.
The lengths give a second check. The WG-011 lead wire at 40 inches is about 101.6 cm, which is slightly longer than the 100 cm lead in the 24-piece set. The SuperDi probe is about 42 inches, or about 106.7 cm, which is longer than the 24-piece set’s 100 cm lead. The WG-011’s stated 47 inch test lead length, about 119.4 cm, is longer than all the other stated lengths. These are conversions of the listed values, not separate measurements.
What the listings do not say
- None of the three states the wire gauge or the conductor material beyond the general terms used in the bullets.
- The 24-piece set does not describe the CAT IV rating that the other two list.
- The WG-011 listing gives two lengths for the same lead, and the SuperDi listing gives one length, for its probe.
- The first listing’s power field reads battery powered, which does not apply to a set of leads.
Related buying guides
For meters that these leads connect to, the multimeter guide covers the main meter types, the multi-meters guide covers multi-function models, and the hand-held digital multimeter guide covers handheld models.
FAQ
Which listings state a CAT IV rating?
The WG-011 listing and the SuperDi listing both state CAT IV 600V. The 24-piece set states CAT III 1000V only.
Which listing states a 20A current rating?
Only the SuperDi listing states 20A, in its title and bullets. The 24-piece set and the WG-011 state 10A.
How long are the leads in each listing?
The 24-piece set lists 100 cm and 70 cm banana plug leads. The WG-011 lists a 40 inch lead wire and a 47 inch test lead length. The SuperDi lists a standard jack probe of about 42 inches.
Are the three sets compatible with the same meters?
The 24-piece set names Fluke, KAIWEETS and INNOVA meters in its title. The SuperDi names Fluke, Ideal and Simpson. The WG-011 lists the multimeter type without naming brands.
What should I confirm before buying?
Confirm the current rating and the category rating your meter and circuit need, the lead length you want, and the connector type on your meter. Check the product page for each, since some figures in these listings sit on different parts of the set.
Bottom line
For a wide range of probes and clips, the 24-piece set lists the most contents. For a pair of silicone leads with a CAT IV 600V figure and clear lengths, the WG-011 is the closer match. For a stated 20A figure, the SuperDi listing is the only one that gives one. Choose by the current rating and the probe style your work needs, and confirm the rest on the product page.
