Best Component Testers Compared by Listed Specs
The person typing best component tester wants a handheld instrument that identifies or measures small parts such as resistors, capacitors, inductors, diodes and transistors, usually off the circuit board. A component tester is a different device from a multimeter. It is built for one job: checking the value and health of a part, not measuring volts, amps and ohms across a live circuit. This guide compares 12 listings using only the specifications and bullet points each listing states. As an Amazon Associate we earn from qualifying purchases.
Quick answer
- For identifying unknown parts and checking transistors, the listings with an auto-identify mode and a transistor socket are the most relevant. The SORINA, FORIOT, HiLetgo and DEWIN LCR-P1 listings all describe that function.
- For precise capacitor, resistor and inductor values, look for a stated test frequency range, test level and open/short calibration. The FNIRSI LC1020E, DEWIN handheld bridge and ZOTEK ZT-DQ02 list the most of these.
- For SMD parts on a board, the FNIRSI LCR-ST1, LCR-ST2 and ZOYI ZT-XC1 list tweezer or spring-clip terminals.
- No listing in this set states an IEC CAT rating. Component testers are not rated for mains measurement, so keep them off live circuits.
What a component tester is, and how it differs from a multimeter
A digital multimeter measures voltage, current and resistance and is the tool for checking whether a circuit has power, continuity or the right voltage. A component tester answers a narrower question: what is this part, and does it behave like a good one? Most listings in this set describe an LCR meter, which means it measures inductance (L), capacitance (C) and resistance (R), often with extra readings such as ESR (equivalent series resistance), Q, D (dissipation factor) and phase angle. Some also identify transistors, MOSFETs, diodes, thyristors and zener diodes.
The two tools overlap only a little. Some listings in this set include a multimeter function, and the ZOYI ZT-XC1 is described as both an LCR meter and a true RMS digital multimeter. Those listings are covered below, but the component-tester function is the part this guide compares. Where a listing is a combined unit, the text says so.
What the specs mean
Test frequency. An LCR meter applies an AC signal at a set frequency. The listings in this set offer 100 Hz, 120 Hz, 1 kHz, 10 kHz and 100 kHz, or a subset. Electrolytic capacitors are usually measured at 100 Hz or 120 Hz, and small ceramic capacitors and RF parts are often measured at higher frequencies. Matching the frequency to the part type can change the reading, so a listing with more frequency choices gives you more room to do this correctly.
Test level. The test voltage applied to the part is listed as 0.1 V, 0.3 V, 0.6 V or 1.0 V in different listings. A lower level is gentler on sensitive parts. A higher level can help on parts with a high threshold. The listings do not explain the trade-off, so treat the number as a setting rather than a quality mark.
Open/short calibration. Several listings describe a calibration routine in which the test leads are left open and then shorted. This removes the error from leads and fixtures. The listings say to do it before measuring, and it is worth doing each time you change probes or fixtures.
Kelvin (four-terminal) connection. Some listings say they use separate current and voltage leads, which the listings describe as reducing lead and contact resistance for low-resistance readings. This matters most for very small resistances.
ESR and secondary parameters. ESR, Q, D, phase angle and reactance are shown as secondary parameters. ESR is the internal series resistance of a capacitor, and a high ESR reading is one reason a capacitor can be faulty even when its capacitance looks normal. The listings give the parameter names but not a pass or fail limit for each, so this guide does not state one.
Auto-identify and transistor tests. Several listings describe an automatic mode that works out the type of part when you clamp or insert it. Transistor and MOSFET tests usually show the pin layout on screen. The listings state which parts each unit identifies. They do not say how accurately a worn or unusual part is identified, so check the readout against the datasheet for critical parts.
Display and interface. The listings state screen sizes from 1.14 inches to 2.8 inches and resolutions where given. A color TFT makes pin diagrams and waveforms easier to read. Some listings add USB output, PC software or data recording for sorting and logging.
Power. Most listings in this set are battery powered, usually with a built-in lithium cell and a USB Type-C charging port. A few list a 9 V battery or a DC input. The power details disagree in some listings, and those cases are noted in the product sections.
Comparison table (listed specs only)
Every figure below comes from the specification table or bullet points on the listing. Where a listing does not give a figure, the cell says “not stated”. Where two parts of the same listing disagree, both figures are shown. The research file for this guide was checked on 2026-10-23.
| Model (brand, ASIN) | Parts it measures or identifies (listed) | Test frequency / test level (listed) | Display (listed) | Power and charging (listed) | Other listed features |
|---|---|---|---|---|---|
| LCR Meter, transistor tester (SORINA, B0H2V9Z8PB) | NPN/PNP transistors, MOSFET, diodes, resistors, capacitors, inductors, thyristors, zener diodes (0.01-30 V) | not stated | Color TFT | Rechargeable lithium battery, USB cable | Test clip, pins, infrared remote decoding, vacuum tube tester per bullet |
| LC1020E LCR meter (FNIRSI, B0FL7QG7MX) | Capacitors 1 pF to 100 mF, resistors 10 mOhm to 10 MOhm, inductors 1 uH to 100 H; ESR, Q, D, theta, X | 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz; 0.1, 0.3, 0.6 V | 2.8 inch TFT, 10 brightness levels | 3000 mAh battery, Type-C | 19,999-count display, sorting and comparison, 3-pin and 5-slot jacks |
| LCR-ST1 tweezers (FNIRSI, B0DBQ4SQGK) | Resistors 10 mOhm to 10 MOhm, capacitors 1 pF to 22 mF, inductors 1 uH to 10 H, diodes | 100 Hz, 1 kHz, 10 kHz; 0.3, 0.6 Vrms | 1.14 inch color | Type-C charging per bullet; battery not stated in specs | Pointed and hook tweezer heads, data export to PC |
| LCR-AR1 (FORIOT, B0HB4G3B9B) | Inductors, capacitors, resistors, transistors, diodes; auto mode identifies type | not stated | 1.9 inch TFT | Specs say “Corded Electric”; bullet says built-in 300 mAh battery; Type-C | SMD socket, NEC infrared decoding, self-calibration by shorting ports 1-2-3 |
| LCR-T4 (HiLetgo, B01MYU0QI3) | NPN/PNP transistors, N- and P-channel MOSFETs, diodes, triodes, resistors, capacitors, SCR | not stated | 128 x 64 LCD | 9 V battery not included; DC 6.8 to 12 V per bullet | Automatic shutdown, MOSFET gate threshold and gate capacitance readings |
| ZT-DQ02 2-in-1 (ZOTEK, B0H7184L2D) | Inductance, capacitance, resistance, impedance; battery internal resistance | 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz; 0.1, 0.3, 0.6 V | not stated | Battery input on separate aviation connector | 4-wire Kelvin, PASS/FAIL sorting, USB-C PC control with SCPI |
| LC1020E LCR meter (WESTOBiG, B0FNDCH78W) | Capacitors, resistors, inductors, diodes, NPN/PNP transistors, MOSFETs | not stated | Title says 2.8 inch TFT; bullet says 2.4 inch | Built-in battery | Auto and manual ranging, 3-pin SMD tweezers clip, test leads |
| ZT-XC1 2-in-1 (ZOYI, B0HGRBN2ST) | Inductance, capacitance, resistance (LCR); true RMS multimeter functions | 100 Hz, 1 kHz, 10 kHz; 0.3, 0.6 V | 2.4 inch TFT | 2000 mAh built-in battery, Type-C | 25,000-count multimeter, gold-plated clips and spring terminals for SMD |
| LCR-P1 transistor tester (DEWIN, B0DW8X2MH8) | Bipolar transistors (10-600), diodes, zener diodes, FETs, IGBT, thyristors, capacitors 25 pF to 100 mF, resistors 0.01 Ohm to 50 MOhm, inductors 10 uH to 1000 uH | not stated | 1.44 inch full-color | 300 mAh Li-ion, Type-C 5 V/1 A | NEC infrared decoding, replaceable SMT socket, automatic capacitor discharge |
| LCR-ST2 tweezers (FNIRSI, B0G1T5D9YL) | Resistors, capacitors, inductors, diodes (up to 0.7 V), voltage (+/-30 V), continuity | 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz; 0.1, 0.3, 0.6, 1.0 V | 1.47 inch HD | 300 mAh, Type-C | Kelvin test clip, curved tip, hooks, primary and secondary display |
| Handheld bridge LC1020E (DEWIN, B0FPPP2284) | AUTO, R, C, L, Z; sub-parameters X, D, Q, theta, ESR; L 0-100 H, C 0-100 mF, R 0-10 MOhm | 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz; 0.1, 0.3, 0.6 V | 2.8 inch TFT | 3000 mAh built-in battery | Basic accuracy 0.3%, 3-terminal and 5-terminal, open/short calibration, data recording |
| Inductance tester, 2 pieces (BTFO, B0H13P2C2Z) | Inductor coils on circuit boards (go or no-go indicator) | not stated | Indicator light only | Power cord per bullet; battery not stated | No measurement values in the listing |
How we chose
This roundup covers the 12 listings in the research file for the keyword “component tester”, checked on 2026-10-23. All 12 are included. None was dropped and none was ranked, because the listings state different things and a fair ranking would need a common test that the listings do not give. The criteria used to group them are the ones in the table: what the listing says the unit identifies or measures, the test frequency and level where stated, the display, the power source, and the extra features such as Kelvin leads, tweezers or data output.
The set includes one narrow product, the BTFO two-pack, which the listing describes as an inductor coil checker with an indicator light and no measurement values. It is listed because it is in the research file for this keyword. It is not a substitute for a full LCR meter. Several listings share the same model number (LC1020E) under different brand names. They are shown separately because each one has its own listing text.
What we could not verify
- None of the 12 listings states an IEC CAT rating, a mains rating or a probe voltage rating. The listing does not state a CAT rating for any unit in this set, and component testers should not be used on mains circuits.
- The listings do not give measurement accuracy for each range, except the DEWIN handheld bridge, which states a basic accuracy of 0.3 percent. The other listings do not give an accuracy figure.
- The FORIOT LCR-AR1 specs say “Corded Electric”, while its bullet point says it has a built-in 300 mAh battery. The listing does not reconcile these, so this guide does not choose between them.
- The DEWIN LCR-P1 gives two different product dimensions: 0.35 x 0.2 x 0.51 inches in the specs and 71 x 87 x 28 mm in the measurement table. The listing does not reconcile them.
- The WESTOBiG LC1020E gives a 2.8 inch screen in the title and a 2.4 inch screen in the bullet points. Both are shown as written.
- The HiLetgo LCR-T4 says the 9 V battery is not included and gives a DC input range of 6.8 to 12 V in its bullet points. The specs table gives no power figure.
- The listings for the transistor and identification units do not state how they handle unusual or worn parts. The sources we opened do not cover these instruments, so no claim is made about accuracy on those parts.
- The listings do not state the actual battery life, weight of the included leads, or the warranty period in a consistent way. Those fields are left blank in the table.
- Pass and fail limits for ESR, Q and dissipation factor are not stated in any listing. This guide does not supply them.
Product picks
{{PICKS}}
1. SORINA LCR Meter, transistor tester (B0H2V9Z8PB)
The listing describes a portable transistor and component tester with a color TFT display. It says it identifies NPN and PNP transistors, MOSFETs, diodes, resistors, capacitors, inductors, thyristors and zener diodes, with a stated range of 0.01 to 30 V for the zener function. The bullet points describe self-calibration, a pin-definition display with an infrared waveform, and a built-in rechargeable lithium battery with auto power off. The included parts are a transistor tester, a USB cable, a test clip and pins. The listing states 3.7 ounces and dimensions of 2.8 x 1 x 3.5 inches.
Skip if you need a stated test frequency or a stated test level. The listing gives neither.
Limit: the bullet points mention a vacuum tube tester function, and the listing gives no further detail on that function.
2. FNIRSI LC1020E 100 kHz LCR meter (B0FL7QG7MX)
The listing describes a handheld LCR and ESR meter with a 19,999-count display. It lists five test frequencies (100 Hz, 120 Hz, 1 kHz, 10 kHz and 100 kHz), test levels of 0.1, 0.3 and 0.6 V, and a secondary display for ESR, Q, D, theta and X. The bullets give ranges of 1 pF to 100 mF for capacitors, 10 mOhm to 10 MOhm for resistors and 1 uH to 100 H for inductors. A sorting and comparison mode uses a nominal value and a tolerance from 0.1 to 99.9 percent, with sound and LED alerts. The listing states a 2.8 inch TFT display, a 3000 mAh battery with auto off, and Type-C charging.
Skip if you need a unit that also measures volts or amps. The listing describes only component measurement.
Limit: the listing says to perform open/short calibration first, to fully discharge capacitors and inductors, and to power off a circuit before measuring onboard parts. It also says not to measure live circuits.
3. FNIRSI LCR-ST1 LCR tweezers (B0DBQ4SQGK)
This is a tweezer-style SMD component tester. The listing gives a weight of 2.86 grams and states three test frequencies (100 Hz, 1 kHz and 10 kHz) and two test levels (0.3 and 0.6 Vrms). Its ranges are 10 mOhm to 10 MOhm for resistors, 1 pF to 22 mF for capacitors and 1 uH to 10 H for inductors. The bullets say it auto-recognizes components, shows D, Z, Q, R and ESR, and exports saved records to a PC through Excel. Two tweezer heads are included: a pointed head and a hook head. The listing says the screen is fixed and does not rotate.
Skip if you need a bench meter with a larger screen. The listing gives a 1.14 inch display.
Limit: the listing states Type-C charging but gives no battery capacity in the specs table.
4. FORIOT LCR-AR1 transistor and LCR tester (B0HB4G3B9B)
The listing describes a multi-function component tester that measures inductance, capacitance and resistance and has a built-in SMD test socket. Its auto mode identifies transistors, diodes, capacitors, inductors and resistors, and a manual mode is available. The listing also says it decodes NEC-protocol infrared signals and shows the waveform. Self-calibration is started by shorting ports 1, 2 and 3 and holding the test button for three seconds. The bullets give a 1.9 inch TFT display and a built-in 300 mAh battery with USB Type-C charging.
Skip if you need a frequency you can confirm from the specs. This listing gives no frequency range.
Limit: the specs table says “Corded Electric” as the power source, which does not match the battery-charging description in the bullets. The listing does not resolve this.
5. HiLetgo LCR-T4 multifunctional component tester (B01MYU0QI3)
The listing describes a component tester with a 128 x 64 LCD and a detection time of about 1.7 seconds, with a note that bulk capacitors can take up to a minute. It identifies NPN and PNP transistors, N-channel and P-channel MOSFETs, diodes, triodes, resistors, capacitors and other devices. For MOSFETs it lists gate threshold voltage and gate capacitance, and for bipolar transistors it lists current gain and base-emitter threshold voltage. The listing says the unit shuts off automatically, with a shutdown current of about 20 nA.
Skip if you need a stated accuracy or test frequency. The listing gives neither.
Limit: the listing says a 9 V battery is not included. It also gives a DC input range of 6.8 to 12 V in the bullets, which the specs table does not repeat.
6. ZOTEK ZT-DQ02 2-in-1 LCR and battery tester (B0H7184L2D)
This unit combines an LCR meter with a battery internal resistance tester. The listing states five test frequencies (100 Hz, 120 Hz, 1 kHz, 10 kHz and 100 kHz), three test levels (0.1, 0.3 and 0.6 V), and automatic, series and parallel equivalent modes. Secondary readings include ESR, D, Q, reactance and phase angle. The battery side is described as measuring internal resistance from 0.1 mOhm to 200 Ohm and DC voltage within plus or minus 100 V. Component sorting uses a nominal value and tolerance with PASS and FAIL results. The listing mentions USB-C connection to a PC with SCPI support.
Skip if you only need a component tester. The battery side adds parts you will not use for circuit boards.
Limit: the battery input uses a separate aviation connector and clips, according to the listing. The listing gives no display size.
7. WESTOBiG LC1020E LCR meter (B0FNDCH78W)
The listing describes an all-in-one component analyzer that identifies capacitors, resistors, inductors, diodes, NPN and PNP transistors and MOSFETs. It has automatic and manual ranging, which the listing says lets you lock a range for stable readings on parts with unknown or fluctuating values. A 3-pin SMD tweezers clip and test leads are included. The bullets describe a built-in battery for cordless use. The listing also states CE, ISO 9001 and RoHS marks.
Skip if you need the exact screen size. The title and bullets differ.
Limit: the listing gives no test frequency, test level or measurement range in its specs table.
8. ZOYI ZT-XC1 2-in-1 LCR meter and multimeter (B0HGRBN2ST)
This is a combined unit. The listing describes an LCR digital bridge for resistance, capacitance and inductance, and a 25,000-count true RMS digital multimeter for AC and DC voltage, resistance, frequency and temperature, with diode and continuity tests. The LCR side lists 100 Hz, 1 kHz and 10 kHz test frequencies and 0.3 or 0.6 V test levels, with ESR, D, Q and phase angle as secondary parameters. The component terminals include gold-plated clips for leaded parts and spring-loaded terminals for SMD parts. The listing gives dimensions of 149 x 76 x 33.5 mm and a weight of 191 g with a built-in 2000 mAh battery.
Skip if you need the component function only. A combined unit has a larger body than a pocket tester.
Limit: the listing does not state a CAT rating for the multimeter function. Do not use the multimeter side on mains without a stated rating for the leads and the meter.
9. DEWIN LCR-P1 transistor tester (B0DW8X2MH8)
The listing describes a pocket transistor and component tester with a 1.44 inch full-color display and a replaceable SMT socket. Its specs table lists ranges for bipolar transistors (10 to 600), zener diodes (0.01 to 4.5 V and 0.01 to 32 V), capacitors (25 pF to 100 mF), resistors (0.01 Ohm to 50 MOhm) and inductors (10 uH to 1000 uH). It also lists FET and IGBT types, thyristor trigger values and battery voltage from 0.1 to 4.5 V. The bullets say an uncharged capacitor is discharged automatically when inserted, and that the unit decodes NEC-protocol infrared signals. It uses a 300 mAh lithium-ion battery with Type-C charging at 5 V/1 A.
Skip if you rely on a stated test level. The specs table does not list a test frequency or level.
Limit: the listing gives two different product sizes, 0.35 x 0.2 x 0.51 inches and 71 x 87 x 28 mm. The listing does not say which is correct.
10. FNIRSI LCR-ST2 LCR tweezers with Kelvin clip (B0G1T5D9YL)
This tweezer-style meter covers resistors, capacitors, inductors, diodes, continuity and voltage. The listing says voltage can be measured up to plus or minus 30 V, and that diode readings go up to 0.7 V. It gives five test frequencies (100 Hz, 120 Hz, 1 kHz, 10 kHz and 100 kHz) and four test levels (0.1, 0.3, 0.6 and 1.0 V), with series and parallel modes. Primary parameters are R, C, L and Z, and secondary parameters are X, D, Q and theta. The kit includes a curved tip, a Kelvin test clip, hooks, a storage bag and a data cable. The listing gives a 1.47 inch HD display and a 300 mAh battery with Type-C charging.
Skip if you only need a fixed bench meter. This unit is a handheld tweezer design.
Limit: the bullets say the range is 1 pF to 22 mF for capacitors, and the specs table does not repeat the range.
11. DEWIN handheld LC1020E digital bridge (B0FPPP2284)
The listing describes a handheld digital bridge with a 2.8 inch TFT display and a 3000 mAh battery. Its main parameters are AUTO, R, C, L and Z, and its sub-parameters are X, D, Q, theta and ESR. The specs give measurement ranges of 0 to 100 H for inductance, 0 to 100 mF for capacitance and 0 to 10 MOhm for resistance, with a basic accuracy of 0.3 percent and five test frequencies from 100 Hz to 100 kHz. The listing states open and short calibration, three-terminal and five-terminal connections, and an internal bias of 0.0 V or 0.5 V. Data recording counts pass and fail results against a nominal value and tolerance. The product list includes a shorting clip, an LC clip kit and a set of multimeter probes.
Skip if you need a voltage or current function. The unit measures components only.
Limit: the listing gives a basic accuracy figure, but it does not say at which frequency or range that figure applies.
12. BTFO inductance tester, 2 pieces (B0H13P2C2Z)
This is the narrowest product in the set. The listing describes two small circuit board inductance testers with an indicator light. The bullets say to plug in the power cord, press the button and bring the sensing end close to the inductor. The light is said to come on when the inductor works and stay off when it does not. The listing names computers, laptops, mobile phones, game consoles and switching power supplies as the target parts. It gives a size of about 7.5 x 2.9 cm.
Skip if you need a number. The listing gives no inductance value, frequency or range, so the unit works only as a pass or fail check.
Limit: the listing does not state a battery, a test frequency or a measurement range. The meaning of “working properly” is not defined.
Buying checklist
- Decide first whether you need a component tester or a multimeter. A component tester measures parts off the board. A multimeter measures voltage and current on a live circuit.
- Check the parts you work on most. Capacitors and inductors need a wide range and a stated test frequency. Transistors need a socket or auto-identify mode.
- Look for open/short calibration in the listing. It removes lead error and is worth having for small values.
- For SMD work, check for tweezers, a SMD socket or spring terminals, as the listings describe them.
- Check the power source and charging port. Several listings disagree about power, so confirm it on the box or manual before buying.
- Look for stated accuracy and a stated range for each parameter. Many listings do not give them.
- If you plan to log data, check for the recording or PC output the listing describes.
Mistakes to avoid
- Measuring a part in a powered circuit. The FNIRSI LC1020E listing says not to measure live circuits and to power off the circuit before measuring onboard parts. The same caution applies to every unit in this set.
- Skipping discharge on capacitors. Fluke’s guide on diodes says that any charged capacitors in the circuit need to be discharged before testing. The DEWIN LCR-P1 listing says it discharges an uncharged capacitor when one is inserted, but that does not replace a check with a multimeter on a charged part.
- Judging a part from one reading. Fluke’s guide on diodes says a diode is best checked by measuring the voltage drop when it is forward-biased, and that a bad diode reads the same in both directions. A single reading on a component tester is not a full diagnosis.
- Using a component tester for a voltage or current job. Most listings in this set do not measure voltage or current. Use a multimeter for those.
- Trusting a spec that the listing does not state. The listings that give no test frequency or accuracy are not a reason to assume either.
Electrical safety first
Work on mains circuits can kill. The component testers in this set are meant for small parts, usually out of the circuit. None of the listings states a CAT rating or a mains rating, so do not use any of them to measure line voltage. Component testers that include a multimeter function, such as the ZOYI ZT-XC1, still need a rated meter and rated leads for mains work. Panel and service work belongs to a licensed electrician.
Fully discharge capacitors before connecting them. Fluke’s guide on diodes says to make sure all power is off and that charged capacitors are discharged before you test a part. The FNIRSI listings give the same instruction for capacitors and inductors.
FAQ
Is a component tester the same as a multimeter?
No. A multimeter measures voltage, current and resistance in a circuit. Most of the devices in this set are component testers or LCR meters that measure the value and behavior of a part. The ZOYI ZT-XC1 is the one listing in the set that combines both functions.
What is an LCR meter?
An LCR meter measures inductance (L), capacitance (C) and resistance (R). Most listings here add ESR, Q, D and phase angle as secondary readings, which describe how a capacitor or inductor behaves at the test frequency.
Which test frequency should I use?
The listings give the frequency choices but not a rule for when to use each one. Check the datasheet of the part, or the instructions in the listing, before choosing. This guide does not give a frequency rule that the sources we opened support for these instruments.
Can a component tester check a diode?
Most listings say they identify diodes, and some give a forward voltage limit. Fluke’s diode guide describes a standard check: measure the voltage drop with the diode forward-biased, then reverse the leads. A good silicon diode shows a drop of about 0.5 to 0.8 V one way and an open reading the other way.
Do I need a component tester for SMD parts?
The tweezer-style listings and the ZOYI ZT-XC1 describe SMD terminals, and the FORIOT and DEWIN LCR-P1 listings describe SMD sockets. If you mostly work on surface-mount boards, check these features first.
Are these units rated for mains?
No listing in this set states a CAT rating or a mains rating. Do not use them on mains circuits.
Is this list complete?
It is complete for the research file for this keyword, checked on 2026-10-23. It is not a full market survey. Other models may exist.
Bottom line
For the widest set of stated ranges and calibration options, the FNIRSI LC1020E, the DEWIN handheld bridge and the ZOTEK ZT-DQ02 list the most specifications. For SMD work on boards, the FNIRSI LCR-ST1 and LCR-ST2 are built around tweezers. For transistor work, the SORINA, FORIOT, HiLetgo and DEWIN LCR-P1 listings describe auto-identify functions. Whatever you choose, check the power and charging details in the listing against the box, and keep any component tester off live circuits.
Related guides: our diode continuity test guide for a narrower look at diode checks, and our guide to multimeters for zener and diode testing for meters that check diodes and zener diodes.
Sources
- Fluke, “How to Test Diodes with a Digital Multimeter”, opened 2026-10-27: https://www.fluke.com/en-us/learn/blog/digital-multimeters/how-to-test-diodes
- Fluke, “What is a Diode? Applications, Testing, and Examples”, opened 2026-10-27: https://www.fluke.com/en-us/learn/blog/electrical/what-is-a-diode
Disclosure: As an Amazon Associate we earn from qualifying purchases.
