Voltage Detector High Voltage: Four Picks Up to 1000 V

As an Amazon Associate we earn from qualifying purchases. Details

A high-voltage detector is a non-contact pen that senses AC voltage through the insulation of a wire, outlet or switch. The four listings below each state a range that tops out at 1000 V AC, which is the top of this group. The figures were checked on 11 October 2026 and are shown as the sellers state them. Each listing describes a pen with an audible alarm and an LED tip.

Quick answer: all four listings state a top of 1000 V AC. The Neoteck, MXCOIRTP and DMwespe listings give a low end of 12 V. The VENLAB offers a switch between a 12 V and a 48 V low end, so pick it if you want to change sensitivity by hand.

The four detectors at a glance

Detector	Listed AC range	Alarm (as listed)	Best fit
Neoteck Non-Contact Voltage Detector (B01JYCVU2Q)	12 to 1000 V	Audible beeps and LED alerts	Home and DIY checks
MXCOIRTP Voltage Tester (B0D7LWBYVW)	12 V, 48 V and 70 to 1000 V	Buzzer alarm with three sensitivity modes	Three named ranges
VENLAB Voltage Tester (B09ZXY4HVK)	12 to 1000 V or 48 to 1000 V	Red tip with high beep, yellow with low beep	Manual sensitivity switch
DMwespe 2 Pack Voltage Detector (B0DPQGPRTV)	12 V, 48 V and 70 to 1000 V	Buzzer with three modes	Two pens in one listing

How we chose these four

We kept a pen when its listing states an AC range with 1000 V as the top and names an alarm. The pool held four listings, and all four pass. Every fact below comes from the listing data alone.

• Top of range: each pick states 1000 V AC as the high end.
• Low end: each names the lowest voltage it detects.
• Alarm: each names the sound or light used.

1. Neoteck Non-Contact Voltage Detector, 12 to 1000 V AC

The title gives a range of 12 to 1000 V AC. The bullets say the pen identifies live and null wires with audible beeps and LED alerts, and that the LED tip lights whenever voltage is detected. It also works as a flashlight. One bullet lists a CE CAT III 600 V safety line, while the title and range give 1000 V. The two are different specifications, and the listing does not explain the gap. The listing gives a weight of 65 g, about 2.3 ounces, and dimensions of 6.3 by 0.79 by 0.79 inches. The warranty is 18 months.

Check the Neoteck detector on Amazon

2. MXCOIRTP Voltage Tester with Three Ranges

The title gives three ranges: 12 V, 48 V and 70 to 1000 V AC. The bullets describe three sensitivity modes. The pen starts in low sensitivity with one buzzer beep, and pressing the S button once enters medium sensitivity, as the listing describes. It has a buzzer alarm, a detection light and a tail flashlight. The listing says the pen shows a low-battery light when the battery drops below 2.5 V. The warranty is one year, and the pen is described as pocket sized with a hook.

Check the MXCOIRTP tester on Amazon

3. VENLAB Voltage Tester with Dual Range

The title gives a dual range of 12 V to 1000 V and 48 V to 1000 V. The listing describes a switch between high and low sensitivity: high covers 12 to 1000 V and low covers 48 to 1000 V. A high-voltage detection makes the tip glow red with a high-frequency beeper. A low-voltage detection makes the tip glow yellow with a low-frequency beep. The pen has a flashlight and a red pointing light, and the listing says it has a three-year warranty. The weight is 0.05 kg.

Check the VENLAB tester on Amazon

4. DMwespe 2 Pack Non-Contact Voltage Detector

The listing is for two pens. Its title and bullets give 12 V to 1000 V AC, and its Item Highlight gives 12 V, 48 V and 70 V to 1000 V. The pens have three buzzer modes, and the default is low sensitivity. Each pen has a detection light and a tail flashlight, and the dimensions are 6.3 by 1 by 1 inches. One bullet uses the same wording as the Neoteck listing, and the detection-light and flashlight bullet matches the MXCOIRTP listing. The listings do not say whether the products are the same.

Check the DMwespe two-pack on Amazon

Worked example: does a 240 V circuit fit the range?

Take a 240 V circuit. Each of the four listings states 1000 V as the top, so 240 V sits well inside every range. Now take a 24 V low-voltage circuit. The MXCOIRTP, DMwespe and Neoteck listings start at 12 V, so 24 V is inside them. The VENLAB high setting starts at 12 V and covers 24 V, but its low setting starts at 48 V, so the listing puts 24 V only inside the high setting. Use the high setting for low-voltage work.

What the listings do not say

• None of the listings gives a detection distance, so the reach of each tip is not known from the listing data.
• The Neoteck listing gives a CAT III 600 V figure next to a 1000 V range. The listing does not explain the difference.
• The MXCOIRTP and DMwespe listings share several bullets, and neither says whether the products are the same.
• No listing gives an independent figure for how often the alarm sounds in each sensitivity mode.

Frequently asked questions

What is the highest AC voltage these pens detect?

All four listings state 1000 V AC as the top of the range.

Which of these pens works down to 12 V?

The Neoteck, MXCOIRTP, VENLAB and DMwespe listings all state 12 V as the low end on at least one setting. The VENLAB low setting starts at 48 V.

Do these pens use a sound alarm?

Yes. Each listing describes a buzzer or beeper. The VENLAB and MXCOIRTP listings also describe tone or sensitivity settings that change the alarm.

Is the DMwespe listing two pens?

Yes. The title says 2 Pack and the listing describes two non-contact voltage detectors.

Conclusion

All four listings state 1000 V AC as the top of the range. For a switchable low end, the VENLAB offers 12 V or 48 V. For three named ranges, the MXCOIRTP listing is the one to read. The DMwespe is the two-pen option. Check the low end against the circuit you plan to test, and read the pen’s own instructions before use.

For more on this kind of pen, see best commercial electric voltage detector, best AC voltage detector and best handheld voltage tester.

Neoteck on Amazon · MXCOIRTP on Amazon · VENLAB on Amazon · DMwespe two-pack on Amazon