Aneng Multimeter Guide: 10 Records Sorted by Job

As an Amazon Associate we earn from qualifying purchases. Details

Someone typing aneng multimeter usually wants one answer: which Aneng meter fits the electrical check in front of them, and whether the listing gives enough detail to decide. Aneng sells pocket multimeters, pen-style meters, clamp meters and a few dedicated voltage testers, and their titles look alike, so the model names and specification blocks matter more than the brand. This guide sorts ten Aneng records by the job each one fits, sets out the ranges and safety wording each listing states, and flags every place where a title, a bullet and a specification block disagree.

Quick answer

• For a pocket meter with a case, the record titled “ANENG Digital Multimeter with Case” (model SZ301) states DC and AC voltage from 200mV to 600V and current from 2mA to 10A in its specification block.
• For a larger count and a body the bullets describe as rechargeable, the 6000-count records (style 620 and the touchscreen model 683) are the strongest candidates here, but both specification blocks list corded electric power, so confirm the power source first.
• For AC current on a single wire, the 4000-count clamp with part number ST181 states 0A to 400A AC, and its bullets say it does not read DC current.
• For a 12V battery or alternator check, the BT172 is a dedicated voltage tester with a 4V to 30V DC range. It is not a general multimeter.

Aneng records grouped by the job they fit

The ten records below fall into four groups. Each entry uses only what the listing states. Where a title, a bullet or a specification block disagrees with another, the entry says so.

Pocket and pen multimeters

The SZ301 record has the most complete pocket listing in this group. Its specification block gives DC voltage at 200mV to 600V with accuracy stated as ±(1%+5), AC voltage at 200mV to 600V with ±(2.0%+10), DC and AC current at 2mA to 10A, resistance from 0Ω to 200MΩ and capacitance from 0nF to 2MF on a 2000-count display. Its bullets add two pre-installed AA batteries, a silicone case, two cable leads, double fuses and overload protection. One bullet is a copied note about dehumidifier voltages. It describes the ranges but says nothing about how the meter is built or protected, so the guide does not treat it as a rating.

The SZ303 record, model SZ303 in its specification block, is the only pocket record here whose listing states a frequency range: 200Hz to 2MHz with an input of 1V to 50V AC RMS. Its bullets also list a backlit screen, a continuity buzzer, a low-battery indicator and two 1.5V AAA batteries. Its voltage and current ranges appear only inside the same dehumidifier note, and its specification block carries no measurement fields.

The pen-style record, model A3005 in its bullets, has no specification block. Its bullets name AC and DC voltage, resistance, continuity, capacitance, diode and live-wire detection, a reverse display, a flashlight, a pen clip and automatic shutdown after five minutes. No numeric range appears, so a buyer who needs one has to read the full listing before deciding.

The XL830L record, part number XL830L-1, adds hFE transistor testing and comes with a 9V battery in the box. A safety bullet gives DC voltage of 200mV to 600V and DC current of 200µA to 10A. The AC voltage range in that same bullet reads 200V to 600V, which looks like a lower limit written with the wrong unit, so the AC low end should be checked on the listing before anyone relies on it.

Smart and large-display multimeters

The 620C record, style 620 with a 6000-count title, lists AC and DC voltage, current, temperature, resistance, capacitance, frequency, continuity, NCV, diodes and live-wire tests. Its bullets describe automatic mode selection, a large LCD with a flashlight, a continuity buzzer, double insulation and overload protection, and a temperature probe in the box. Its specification block says the power source is corded electric, while the bullets describe a rechargeable battery charged through a Type-C cable. Where a listing disagrees with itself, this guide follows the bullets and states the conflict, so the rechargeable claim is a bullet claim that the specification block contradicts. Part of the bullet text is also written in German.

The touchscreen record, model “Multimeter 683″, shares much of its bullet text with the 620C. It describes a color touchscreen with a reverse display, data hold, a built-in flashlight, an analog bar graph, real-time temperature monitoring and the same rechargeable Type-C power. Its specification block repeats the corded-electric field and gives an item weight of 200 g. One sentence about the test lead reads as garbled copy, so no wire rating can be taken from it, even though the surrounding bullets are readable.

The 613 record, model 613 with a 4000-count title, is a large-screen auto-ranging meter covering AC and DC voltage, current, ohms, continuity, capacitance and temperature. Its bullets stress a large backlit display, data hold and a low-battery indicator, and add a calendar, an alarm clock and a temperature readout. Those extras do not measure electrical values, so they should not drive the choice. Its item-weight field reads 0.6 g, which is not a plausible weight for a handheld meter, so that field should be checked before anyone relies on it.

Clamp meters

The 4000-count clamp, part number ST181 with the style “4000 Counts AC Current”, is the more specific of the two clamps. Its specification block gives AC current from 0A to 400A, AC and DC voltage from 0V to 600V, resistance to 40MΩ, capacitance to 4mF and frequency to 4MHz, on a 4000-count display. Its DC current field reads none, and the bullets confirm that the clamp does not read DC current. The jaw takes a conductor up to 1.42 inches across, which converts to 1.42 x 25.4 = 36.07 mm. The bullets also say to press REL to zero the meter before clamping, and they list NCV detection.

The PN200 clamp, model PN200, carries 600A AC/DC in its title, and its bullets say it reads both AC and DC current. Its jaw takes a conductor up to 1.33 inches across, which converts to 1.33 x 25.4 = 33.78 mm. Neither the bullets nor the specification block gives a DC current range, so the 600A figure rests on the title alone. The package includes a charging cable, a combination lead set and a storage bag.

Battery and voltage testers

The BT172 is a 12V battery tester, not a general multimeter. Its specification block classifies it as a voltmeter. Its bullets state a test range of 4V to 30V DC, with LO shown below 4V and HI above 30V, reverse-connection protection, three modes for checking the alternator and the battery, and an accuracy of about 0.01V. The bullets list cars, trucks, motorcycles, boats, mowers and golf carts as applications. It is a narrow tool, and the accuracy figure is the listing’s own claim.

Ranges and counts side by side

The table uses only figures printed in the specification blocks or bullets. A blank cell means the listing does not give that figure.

Record (listing model)	Measurement type	Voltage stated	Current stated	Count or display
SZ301 pocket meter	Multimeter	DC and AC 200mV~600V	DC and AC 2mA~10A	2000 count
XL830L	Multimeter (bullets)	DC 200mV~600V; AC 200V~600V (bullet)	DC 200µA~10A (bullet)	not stated
620C	Multimeter	not stated	not stated	6000 count (title)
ST181 clamp	Multimeter, Voltmeter	AC and DC 0V~600V	AC 0A~400A; DC none	4000 count
PN200 clamp	Multimeter, Voltmeter	not stated	AC and DC (title: 600A)	4000 count (style)
BT172 battery tester	Voltmeter	4V to 30V DC (bullet)	not applicable	not stated

Two calculations follow from these listings. The first compares display counts: a 2000-count display splits a range into at most 2000 steps and a 6000-count display into at most 6000, so 6000 / 2000 = 3. That means three times as many possible readings across the same range. It says nothing about accuracy, which only the SZ301 and BT172 listings state at all. The second is the unit conversion for the two clamp jaws, 1.42 x 25.4 = 36.07 mm and 1.33 x 25.4 = 33.78 mm, which turns the inch figures in the bullets into millimeters.

How we chose

The ten records come from the Aneng pool. We kept a record when its listing names a multimeter, a clamp meter or a voltage tester, and when its title, bullets and specification block agree on the main measurement. We also looked for a stated range, count or safety figure, because a reader cannot check a meter whose listing gives none.

Two records were set aside. One is a non-contact voltage pen sold with screwdriver bits. Its title leads with the screwdriver, which makes it a hand tool with a voltage detector, outside this roundup. The other is a basic multimeter with a case whose bullets name measurement types but give no range, count or safety figure. Both remain Aneng records, so a reader who wants them can check the listing directly.

No Aneng listing in this group states a CAT measurement category, so this guide does not assign one.

Where the listings disagree

• The 620C and the touchscreen 683 specification blocks both say corded electric, while their bullets describe a rechargeable battery and a Type-C charging cable. The bullets are followed here, and the power source should be confirmed before purchase.
• The ST181 clamp’s specification block gives an item weight of 0.6 g and a separate weight of 129g. Both fields cannot be right.
• The PN200 title gives 600A, but neither its bullets nor its specification block give a current range.
• The XL830L AC voltage bullet reads 200V to 600V, while the DC low end in the same bullet is 200mV.
• The SZ301 and SZ303 bullets include a copied dehumidifier note. It reads as a range statement only and says nothing about the meter itself.
• Part of the 620C bullet text is written in German.

How to choose by task

Start with the reading you need. For a household check of outlets, batteries and continuity, the SZ301 pocket meter has the clearest stated ranges, and the pen-style record is the smallest option, though it has no numbers to compare. For a 12V vehicle battery or alternator, the BT172 is the dedicated choice. For current in a single conductor without breaking the circuit, the ST181 clamp states the AC current range in this group, while the PN200 is the only clamp whose bullets claim DC current, and its range has to be confirmed on the listing. For a larger display with auto-ranging, the 620C and the 613 are the records to read first.

If you are weighing a non-contact pen instead of a meter, the pen voltage detector picks cover that category. The auto-ranging multimeter picks describe the wider market for meters that set their own range, and the true RMS clamp meter picks cover the clamp category more broadly.

Safety before you measure

The OSHA electrical overview says electricity has long been recognized as a serious workplace hazard, and that OSHA’s electrical standards aim to protect people from electric shock, electrocution, fires and explosions. OSHA’s rule on work practices says a qualified person uses test equipment to test the circuit elements and electrical parts of equipment, and that live parts must be de-energized before a worker works on or near them.

The Purdue extension sheet says voltage is the difference between two points, such as the two ends of a battery, and that the measuring principles are the same for DC battery work and AC house wiring. It also says working with live circuits can be very hazardous without proper tools and safeguards, and that a user should move cautiously while probing.

Mains wiring and car electrical work should be left to a qualified person. A meter with a stated voltage range is not a substitute for knowing the circuit, and the listings here give no procedure for mains work. Follow the manual that comes with the meter, and do not use a meter whose stated range does not cover the circuit you expect.

What we could not verify

• Accuracy. The SZ301 and BT172 listings print accuracy figures, but the documents we opened do not cover Aneng’s accuracy, so those figures are the listing’s own claims.
• Safety category. The carded listings give no CAT category, and the clamp and pocket records give no CAT figure in any field.
• Power source. The 620C and 683 conflicts cannot be resolved from the listings.
• The PN200 600A current range and the XL830L AC low end.
• Clamp jaw sizes, display counts and NCV sensitivity come from the listings only, and the documents we opened do not cover them.
• Whether any Aneng manual for these models gives ranges that differ from the listing.

FAQ

Which Aneng meter suits a home user who wants one meter?

The SZ301 pocket record has the most complete specification block in this group, with DC and AC voltage and current ranges and a 2000-count display. Its listing gives no CAT category, so treat it as a general-purpose household meter rather than a rated tool for mains work.

Does a 6000-count display make an Aneng meter more accurate?

No. A higher count gives finer steps across a range, which the calculation above shows as three times the steps of a 2000-count display. Accuracy is a separate figure, and only some listings state it at all.

Can an Aneng clamp meter read DC current?

It depends on the record. The ST181 clamp states that it reads AC current only. The PN200 bullets say it reads AC and DC current, but no DC range is given, so confirm that on the listing before relying on it.

Is the 12V car battery tester a multimeter?

No. The BT172 is a dedicated battery and alternator tester with a stated 4V to 30V DC range. It suits a car or small engine check, but it does not replace a multimeter for other jobs.

Do these listings give a safety rating for mains work?

The listings here do not give a safety category for mains work. A stated voltage range describes what the meter reads, not what it can safely be used on, and mains and car electrical work should be done by a qualified person.

What should I check on an Aneng listing before buying?

Read the power field, the range line and the count together. The 620C and the touchscreen 683 show why: a corded power field beside a rechargeable bullet means the listing needs a second look before purchase. Check whether a DC or AC current range is printed, because some titles name a current or a voltage that the bullets never repeat. Finally, look for a stated safety category. The Aneng records here do not give one, so the listing alone cannot settle a mains question.

Bottom line

Choose the record by the measurement you need, then confirm the range or power field the listing states. When a specification block and the bullets disagree, check the listing before buying, and leave mains and car electrical work to a qualified person.

Sources

• Electrical (OSHA overview): electrical hazard and standards context for the safety section.
• 29 CFR 1910.333, Selection and use of work practices (OSHA): qualified person test equipment and de-energizing wording.
• Voltage Meter Basics (Purdue University Cooperative Extension, 4-H project sheet, PDF): voltage as a difference between two points and the hazard of live circuits.