Electrical Cable Megger Test: 4 Insulation Testers Compared
As an Amazon Associate we earn from qualifying purchases. Details
An electrical cable megger test measures how much current leaks through a cable’s insulation, and it reports the answer in megohms. You need a real insulation tester for it, because a normal multimeter applies far too little voltage. Four of the products reviewed qualify, each from a different brand, and this guide sorts them by the things that matter on cable work: test voltage steps, measurement range, protection against live conductors and how easy the readings are to record. It also covers the mistakes that make a good cable look bad, and when the job should go to a licensed electrician instead of you.
Quick answer
For a wide choice of test voltages, from 50V up to 1000V, the fourth pick is the only one that lists five steps. For a selectable 250V, 500V or 1000V tester that also reads up to 2GΩ and works as a multimeter, take the third pick. For a dedicated case with a weatherproof rating, the first pick is the one. For a fixed 500V check with a plain analog scale, the second pick is the simplest.
None of the four listings states a CAT rating. That matters if you plan to use the tester on live circuits, so read the manual before doing so. Mains circuits can kill, and panel or service work belongs to a licensed electrician.
Why a megger test for cables needs different specs
A megger test for cables has its own pressure points. A cable is a long insulated run, and the test lead ends can be metres apart. Fault patterns differ from a motor winding: damage may sit at one bend or one buried joint, and the cable may still be connected at both ends.
For that reason, these five checks carry the choice.
Test voltage steps
A cable has a rated voltage, and the test voltage should match what the cable’s maker or the job specification asks for. The fourth pick lists 50V, 100V, 250V, 500V and 1000V. The third lists 250V, 500V and 1000V DC. The first lists 250, 500 and 1000 V. The second is fixed at 500V. A wider ladder gives you room to start low on older or lower-rated cable, though the choice itself comes from the cable’s documentation, not from the tester. See the best megger test voltage for more on matching voltage to the job.
Measurement range
The second pick measures up to 1000 MΩ. The third reads from 0.1MΩ to 2GΩ with a stated ± 4% accuracy. The first lists “1000 Megaohms Resistance” as its style, and the fourth listing does not state a range. A common rule of thumb is that insulation resistance reads lower as a cable run gets longer, because more insulation is in parallel, so headroom helps on long runs.
Live circuit protection
A cable that looks dead may still carry voltage from a neighbouring circuit or stored charge. The fourth pick says live circuit detection prevents an insulation test if voltage greater than 30-Volts is detected. The first lists a live circuit warning. The third mentions a high voltage and short circuit buzzer alarm. The second lists no equivalent. Treat any of these as a backstop, not a substitute for isolating and proving the cable dead first.
Reading and recording
On cable work you often read, move the leads, and read again. The third pick has data hold, a 3.5″ backlight LCD and a sampling rate of approximately 3 times per second. The fourth has a large backlit display and a remote test probe for repetitive or hard-to-reach testing. The second uses an analog Good, Caution and Bad scale, which is quick but gives no number to log.
Safety paperwork
The first lists IEC 61326 and Iec61010-1, the fourth EN 61010-1, and the third CE and RoHS. The wider point is that measurement category is an IEC classification of circuits by available energy and impulse voltages, and the required impulse withstand voltage runs from 500 V (CAT II, 50 V) to 12,000 V (CAT IV, 1000 V). Without a stated category, keep these testers to isolated, de-energised cable.
Insulation testers that fit an electrical cable megger test
Four products qualify, each from a different brand. The cards below carry specs, pros and cons from each listing.
1. Megger MIT310-EN Digital/Analog Insulation Tester, 250/500/1000 V Test Voltage (Best for damp or outdoor runs)
Specs from the listing (checked 2026-10-11):
- Brand: Megger
- Power Source: Battery Powered
- Item Weight: 2.2 pounds
- Item Dimensions: 4.25 x 11 x 12 inches
- Measurement Type: Ohmmeter, Voltmeter
- Specification Met: IEC 61326, Iec61010-1
Pros
- Weatherproof to IP54 with a rubber armoured case
- Lists a live circuit warning
- Selectable 250, 500 and 1000 V test voltage
Cons
- Largest of the four by listed size at 4.25 x 11 x 12 inches
- The listing does not state a CAT rating or whether batteries are included
Best for: Cable runs outdoors or in damp plant rooms where a rugged case matters.
Skip if: You want multimeter functions such as current or capacitance.
View on Amazon (affiliate link)
2. M500 Megohmmeter Insulation Tester, 500V Digital Megger Meter Measures Up to 1000 MΩ, Portable HVAC (Best for simple 500V checks)
Specs from the listing (checked 2026-10-11):
- Brand: ToolSentryX
- Power Source: Battery Powered
- Compatible Devices: Electrical devices and systems
- Model: M500
Pros
- Analog scale with Good, Caution and Bad zones
- Measures up to 1000 MΩ at a stable 500V
- Soft carrying pouch included
Cons
- Output fixed at 500V
- The listing gives no weight, dimensions or CAT rating and has no numeric display
Best for: A quick pass-or-fail check on a cable that should be tested at 500V.
Skip if: You need other voltages or numbers to log.
View on Amazon (affiliate link)
3. VC60B Digital Insulation Resistance Tester, Electrical Megaohm Meter with 250V/500V/1000V Test (Best digital with multimeter)
Specs from the listing (checked 2026-10-11):
- Brand: SKYCENX
- Power Source: Battery Powered
- Item Weight: 2.5 kg
- Item Dimensions: 7.28 x 4.53 x 2.56 inches
- Measurement Type: Ohmmeter
- Specification Met: CE, RoHS
Pros
- Shows the insulation resistance value, not just a range
- Reads from 0.1MΩ to 2GΩ
- 1999 counts multimeter with AC voltage to 750V and a continuity buzzer
Cons
- Listed weight of 2.5 kg and size of 7.28 x 4.53 x 2.56 inches do not fit together, so rely on neither
- The listing does not state a CAT rating
Best for: Logging numeric readings on cable runs and heated cable work.
Skip if: You need a stated CAT rating or reliable size and weight figures from the listing.
View on Amazon (affiliate link)
4. Fluke 1507 Digital Megohmmeter Resistance Tester for Advanced Industrial and Electrical Testing (Best for voltage steps and live lockout)
Specs from the listing (checked 2026-10-12):
- Brand: Fluke
- Power Source: Alkaline
- Item Weight: 500 g
- Item Dimensions: 11.77 x 15.2 x 3.07 inches
- Measurement Type: Ohmmeter
- Specification Met: EN 61010-1
- Included Components: Remote probe, test leads, test probes, alligator clips and one-year warranty
Pros
- Five test voltages from 50V to 1000V
- Blocks an insulation test if voltage greater than 30-Volts is detected
- Remote probe, test leads, probes and alligator clips included
Cons
- Ohmmeter only, with no multimeter functions listed
- The listing does not state a CAT rating or a top range figure
Best for: Repetitive or hard-to-reach cable work where lower voltage steps may be needed.
Skip if: You want one device that also measures voltage or current.
View on Amazon (affiliate link)
How each pick behaves on cable work
First pick: dedicated tester in a rubber case
This one is a Digital/Analog tester with a test voltage choice of 250, 500 or 1000 V. The listing gives 2.2 pounds in weight and 4.25 x 11 x 12 inches in size, a tough rubber armoured case, a self contained protective cover, IP54 weatherproofing, a live circuit warning, a three-year warranty and a calibration certificate.
For cable runs outdoors or in a damp plant room, the weather rating is the useful detail. Limits: it lists only Ohmmeter and Voltmeter as measurement types, states no CAT rating and does not say whether batteries come with it. Skip it if you want a multimeter’s current or capacitance range.
Second pick: fixed 500V with an analog scale
The second pick outputs a stable 500V, measures up to 1000 MΩ and lists wiring among the things it checks. Its analog scale is divided into Good, Caution and Bad zones. The enclosure is a double-layer ABS housing, and a soft carrying pouch is included.
It is the simplest of the four, and its limits follow from that. The output is fixed, the listing gives no weight or dimensions, and there is no numeric display, so you cannot log a figure to compare next visit. Skip it if your cables call for a voltage other than 500V.
Third pick: digital tester with a multimeter built in
This tester offers 250, 500 and 1000V DC from 0.1MΩ to 2GΩ with a stated ± 4% accuracy. It displays the insulation value specifically, not just a range. As a multimeter it has 1999 counts and measures AC voltage up to 750V with ±1.0% accuracy, plus a continuity buzzer. The listing names heated cable, floor heating cable, thermostats and wiring among its uses.
Two fields deserve caution. The listing gives a weight of 2.5 kg and dimensions of 7.28 x 4.53 x 2.56 inches, and it also lists 32 items. Those numbers do not fit together comfortably, so rely on neither and check the listing before relying on the size or weight for portability. The data hold function is also described with a limitation, so read the full listing text. Skip it if you want a CAT rating on paper, since none is stated.
Fourth pick: five voltage steps and live-circuit lockout
It weighs 500 g and measures 11.77 x 15.2 x 3.07 inches. It uses alkaline power, comes with a remote probe, test leads, test probes, alligator clips and a one-year warranty, and has a large backlit display. It also states EN 61010-1, a NIST-traceable calibration certificate with data, and live circuit detection that blocks an insulation test if voltage greater than 30-Volts is present.
The remote probe helps on repetitive work or cable ends that are hard to reach. Limits: it is an Ohmmeter only, it does not list a CAT rating, and the listing does not state a top range figure in the specs. Skip it if you want a multimeter in the same body.
Side-by-side comparison
| Feature | First pick | Second pick | Third pick | Fourth pick |
|---|---|---|---|---|
| Test voltages | 250, 500, 1000 V | 500V | 250V, 500V, 1000V | 50V, 100V, 250V, 500V, 1000V |
| Range | 1000 Megaohms Resistance (style) | up to 1000 MΩ | 0.1MΩ to 2GΩ | not stated |
| Live protection | Live circuit warning | Not listed | Buzzer alarm | Blocks test above 30-Volts |
| CAT rating | Not stated | Not stated | Not stated | Not stated |
| Warranty | three-year | Not stated | Not stated | 1-Year |
| Extras | IP54, rubber case | Soft pouch | Multimeter, data hold | Remote probe, accessories |
Which to choose for your cable job
You test long or buried runs and want to log results. The third or fourth pick suits you. The third gives a numeric value and data hold, and the fourth gives a remote probe and a high-contrast display.
You work outdoors or around moisture. The first pick is the only one with a stated weatherproof rating, IP54. Wear the usual protective gear and follow the manual.
You only need to confirm that one 500V cable passes. The second pick is enough. It tells you Good, Caution or Bad, though not by how much.
You are unsure what voltage the cable should see. Do not guess. A wider ladder helps, but the cable documentation or an electrician should supply the number. See also how to do a megger test, cable insulation testing and the guide on high potential testing for cable.
Suppose a crew checks 12 cables, and each cable has 3 insulated conductors plus a metal screen. The plan is to read every conductor against every other conductor, and each conductor against the screen.
Conductor-to-conductor pairs: 3 conductors give 3 pairs. Conductor-to-screen readings: 3. Total per cable: 3 + 3 = 6 readings.
For the batch: 12 × 6 = 72 readings. If each reading takes 1.5 minutes including moving leads, 72 × 1.5 = 108 minutes, which is 1 hour 48 minutes. Check: 108 ÷ 60 = 1.8 hours, and 0.8 × 60 = 48 minutes, so the answer holds.
Now suppose one conductor reads 200 MΩ at 500V. Leakage current is voltage divided by resistance: 500 V ÷ 200 MΩ = 2.5 µA. Check: 2.5 µA × 200 MΩ = 500 V. At 1000V with the same resistance the current doubles to 1000 V ÷ 200 MΩ = 5 µA, and 5 µA × 200 MΩ = 1000 V.
With 72 readings to take, a recordable display and a remote probe save more effort than a rating you will rarely approach. If every reading is near the top of a 1000 MΩ range, the 2GΩ range of the third pick has more room.
Common mistakes on an electrical cable megger test
- Testing a cable that is still connected to equipment. Connected loads, drives and electronics change the reading and can be damaged. Follow the instrument manual and the equipment maker’s instructions.
- Picking the test voltage by what the tester offers. The cable’s rating should drive the choice. A tester that reaches 1000V is no reason to use 1000V.
- Assuming a cable is dead because it looks dead. Prove it with a voltage check first. See what a voltage meter does if you need a refresher.
- Comparing a long run to a short one. The longer run will read lower for the same insulation, so compare like with like and keep a record.
- Treating the analog Good zone as a specification. It is a quick screen. For a pass or fail against a standard, use the number and the standard.
For adjacent jobs, see the best megger test for wire, motor megger testing and insulation resistance test equipment.
FAQ
What does an electrical cable megger test show?
It shows the resistance of the insulation in megohms at a chosen DC test voltage. A high steady reading points to sound insulation. A low or dropping reading points to moisture, damage or contamination.
Can I use my multimeter for a megger test for cables?
Not for a true insulation test. A standard multimeter ohms range uses a few volts, so it will not stress the insulation. Choose a tester that lists a test voltage such as 500V or 1000V.
Which test voltage should I pick for a cable?
Use the voltage specified by the cable maker or the job documents. The fourth pick has the widest range of steps, from 50V to 1000V, and the second pick has only 500V.
Do any of these testers state a CAT rating?
No. The listings do not state a CAT rating. Keep use to isolated cable and read the manual before any live work.
Is it safe to test a cable that might be live?
The fourth pick blocks a test above 30-Volts and the first lists a live circuit warning, but neither replaces proving the cable dead. Mains work can kill, and panel or service work belongs to a licensed electrician.
Do I need data hold?
It helps when the display is hard to see while the leads are in place. The third pick lists data hold with a note on a limitation, so check the listing text for details.
What if the listing details look wrong?
Do not rely on suspect fields. For example, the weight and size listed for the third pick do not sit well together. Contact the seller or read the manufacturer’s manual.
Bottom line
Choose the fourth pick for the widest set of voltage steps and live-circuit lockout. Choose the third for a digital reading, 2GΩ range and multimeter use, and verify its size. Choose the first for a weather-rated case. Choose the second for fast 500V checks only. If your cable calls for a voltage outside what your pick offers, change the tester, not the test.
Sources
- Measurement category (Wikipedia): explains CAT classification and the 500 V to 12,000 V impulse withstand range






