As an Amazon Associate we earn from qualifying purchases. This page contains no product links.
The Centech 61593, sold under the Cen-Tech name, is an 11-function handheld digital multimeter. It covers AC and DC voltage and current, resistance, capacitance, frequency, temperature, continuity, diode and transistor tests. This guide explains how to set up the 61593 and take basic measurements, using the ranges and ratings from two readable pages. Where the two sources disagree, we say so.
Quick answer
The Centech 61593 is an 11-function handheld meter with 2000 counts and one 9V battery. Its listed DC voltage maximum is 1000 V. The fuse ratings conflict between the two sources, so check the fuse marking before you replace a fuse.
How we chose
We looked for two readable pages that we could open ourselves and used only the figures those pages state. We did not use search-result summaries, forum estimates, or pages that returned an access block. Where two sources disagree, we list the disagreement under “What we could not verify” rather than picking one value.
What the 61593 measures
The eBay listing we opened lists the 61593 with 2000 counts and an 11-function set that includes AC and DC voltage, AC and DC current, resistance, capacitance, frequency, temperature, continuity, diode, transistor and logic tests. Humidity and sound level also appear in that listing, but the manual page we opened does not list them, so treat those two as listing claims only.
The manual summary page gives the voltage ranges as DC from 200 mV to 1000 V and AC from 200 mV to 700 V, with a maximum input of 1000 V DC or 700 V AC on a sine wave. The eBay listing gives the same DC maximum and a 2 V to 700 V AC range.
Listed ranges
- DC voltage: 200 mV, 2 V, 20 V, 200 V and 1000 V.
- AC voltage: 200 mV, 2 V, 20 V, 200 V and 700 V.
- DC and AC current: 200 µA, 2 mA, 20 mA, 2 A and 10 A on the manual summary page.
- Resistance: 200 Ω, 2 kΩ, 20 kΩ, 200 kΩ, 2 MΩ and 20 MΩ.
- Capacitance: 2 nF, 20 nF, 200 nF, 2 µF and 20 µF.
- Frequency up to 20 kHz.
- Temperature with a K-type probe, from -20 °C to 1000 °C.
The current section of the manual page also refers to a 20 A position in its operating notes, but the spec table does not list one. Check the physical dial on your unit before you rely on a 20 A setting.
Step 1: Install the battery and check the leads
The manual summary page says the meter runs on one 9 V battery, which is included. When the battery symbol appears on the display, replace the battery before you take important measurements. Check the test leads for cracked insulation and worn tips before each use.
Step 2: Choose the function and range
Turn the dial to the function you need. For household AC voltage, choose AC voltage and set a range above the expected value. For a DC battery check, choose DC voltage. If the display shows an overload, move to a higher range.
Step 3: Connect the leads
Use the COM jack for the black lead. For voltage and resistance, the red lead goes in the V-ohm jack. For current, use the mA or 10 A jack that matches the range. The eBay listing describes fused current terminals and a glass fuse and an HRC fuse for input protection, so check the fuse condition if a current reading suddenly reads zero.
Step 4: Take the measurement
Touch the probes to the test points and read the display once it settles. For resistance and continuity, de-energize the circuit first. The continuity function is useful for a quick open-wire check, but confirm an important result with the resistance range.
Step 5: Use the temperature mode
The temperature function uses a K-type probe. Plug the probe into the correct input, select the temperature function, and wait for the reading to settle. Keep the probe in contact with the surface you are measuring, and avoid reading air temperature when you need a surface value.
Safety and category
The eBay listing gives a CAT III rating, and the manual summary page gives the maximum input voltage. We did not find a readable page that states the full category for each range, so do not assume a higher category applies. Use the meter only within the voltage and category printed on your unit.
If you are choosing a first multimeter, our guide to the Klein non-contact voltage detector explains when a pen-style tester is the better quick check. For a basic comparison of voltage testers and meters, see the Klein tool voltage tester how-to guide.
Troubleshooting the 61593
If the meter gives no reading on a function you expect to work, first check the battery symbol on the display, then confirm the dial position. If current readings are zero, check the fuse in the current path, since the eBay listing names glass and HRC fuses in the input protection. A temperature reading that seems wrong often comes from the probe sitting in air instead of on the surface, so press it firmly against the material. A continuity tone that appears unexpectedly can come from a parallel path, so check the circuit with the power off and isolate the component if needed. For long storage, remove the battery, and keep the leads and probe tips clean so the connections stay reliable.
The 61593 is a general-purpose meter, so it covers many common tasks but does not offer the features of a higher-end instrument. Its listed functions suit home repair, car electrical checks, and light electronics. For a battery or a fuse check, the current and continuity functions are the most useful. For a precise measurement, a meter with a published accuracy table and a clearly stated safety category is a better choice. If you use the 61593 on a higher-energy circuit, confirm the category on your own unit’s label first, since the sources we could open do not agree on every fuse and category detail.
What we could not verify
- The fuse ratings. The manual summary page gives two conflicting fuse entries: a fast-acting 200 mA, 250 V fuse in the spec table and a 2 A, 250 V quick-acting fuse in the maintenance section. The eBay listing names the fuse types but not their ratings. Check the fuse marking on your own meter before replacing it.
- The accuracy specification. Neither readable source gives a percentage of reading and digit tolerance for each range.
- The official Harbor Freight or Cen-Tech manual. Search results pointed to a Harbor Freight manual, but we could not open that page, so this guide does not rely on it.
- The humidity and sound level functions listed on eBay. We did not find them on the manual summary page.
- The 20 A current position. The operating notes mention it, but the spec table does not.
FAQ
How many functions does the Centech 61593 have?
The eBay listing says 11, including voltage, current, resistance, capacitance, frequency, temperature, continuity, diode, transistor and logic tests.
What battery does it use?
One 9 V battery, according to the manual summary page.
What is the maximum voltage?
The manual summary page gives 1000 V DC or 700 V AC on a sine wave.
Is it CAT III rated?
The eBay listing says CAT III. We did not confirm that on a manufacturer page.
Does it measure temperature?
Yes, with a K-type probe, from -20 °C to 1000 °C according to the manual summary page.









